V2 Robot Vacuum User Guide

I. Operating Steps

1. Assembly

Install the operating handle, adjust the direction of the handle’s end, and insert it into the vacuum cleaner's port following the arrow direction. When you hear a “click” sound, ensure the handle is firmly secured without any looseness, indicating successful installation.

2. Charging

Connect the power supply of the self-cleaning base and place the robotic vacuum on it. When you hear a “ding-dong” sound and the screen displays the charging animation, the vacuum has started charging.

3. Startup

3.1. Filling the Clean Water Tank

Remove the clean water tank from the vacuum’s base and open the water inlet cover. Add clean water first, then pour in the cleaning solution to prevent excessive foam. Once filled, close the water inlet cover and place the tank back in the base.

3.2. Unlocking & Startup
  1. Electrolyzed water sterilization will not activate in Quick Suction mode.
  2. After turning on, the device will be in a paused state. Move the operating handle to unlock and start cleaning, or move the handle first and then short press the power button.

4. Button Operations

4.1 Mode Button

This is a physical mechanical button with different functions depending on the vacuum’s status:

  1. During floor cleaning:
    • Short press → Switch modes (Smart/Strong/Quiet/Quick Suction).
    • Long press → Activate MAX Boost mode, release to exit MAX Boost.
  2. During self-cleaning or when charging screen is on:
    • Short press → Enable drying mode only.
  3. When charging screen is on:
    • Long press (2s) → Turn voice function on/off.
4.2 Power Button

This is a physical mechanical button with different functions depending on the vacuum’s status:

  1. During floor cleaning:
    • Short press → Power on/Pause.
    • Long press (2s) → Power off.
  2. During self-cleaning or drying:
    • Short press → End task.

II. Cleaning Modes

1. Mopping Mode

Cleaning Modes
  • Smart Cleaning
  • Quick Suction
  • Strong Cleaning
  • Quiet Cleaning
  • MAX Boost
Voice Interaction
  • Smart Cleaning
  • Quick Suction
  • Strong Cleaning
  • Quiet Cleaning
  • MAX Boost Activated
Mode Descriptions
  • Smart Cleaning: The recommended mode for home use. It detects dirt levels and adjusts suction power and water supply accordingly, ensuring efficient cleaning.
  • Quick Suction: Designed for water stains and carpets, particularly effective in bathrooms and short-pile carpet areas.
  • Strong Cleaning: Increases suction power and water flow, ideal for deep cleaning heavily soiled floors.
  • Quiet Cleaning: Reduces noise and extends battery life.
  • MAX Boost: Press and hold the mode button to activate the most powerful cleaning mode. Release the button to return to the previous mode.
Power Settings

  • High Dirt Levels:

    • High fan speed, high brush speed, water supply off.
    • High fan speed, high brush speed, high water supply.
    • Lowest fan speed, high brush speed, lowest water supply.
    • Maximum fan speed, maximum brush speed, maximum water supply.

  • Low Dirt Levels:

    • Low fan speed, high brush speed, low water supply.

2. Self-Cleaning Mode

Operating Steps

Place the vacuum back onto the base, connect the power, and short press the self-cleaning button to enter self-cleaning mode.

Self-Cleaning Process
  • Recommended: Run self-cleaning after each use.
  • Cleaning Duration: 1-4 minutes, dynamically adjusted based on dirt levels and water supply.
  • Drying Duration: 30 minutes.
Self-Cleaning Voice Interaction
Voice Prompt Trigger Condition Status
Start drying brush roller Brush roller detected in position, drying starts Drying
Start drying brush roller and wastewater tank filter Both roller and filter detected, drying starts Drying
Start drying wastewater tank filter Filter installation detected Drying
Drying wastewater tank filter completed Filter removal detected Drying completed
Self-drying completed, starting charging Manual drying stopped Charging
Self-cleaning completed, starting charging Manual cleaning stopped Charging
Voice Prompts & Conditions
Voice Prompt Trigger Condition Function
High dirt detected, please perform self-cleaning Dirt level remains high for 30s during cleaning Dirt sensor detection
High dirt detected, please add water and perform self-cleaning Dirt level remains high for 30s, water level below 10% Dirt sensor & water level detection
Wastewater tank removed Tank removed during standby/charging Wastewater tank detection
Please place the vacuum correctly to prevent dirty water backflow Tilt angle less than 10° for over 5s in standby mode Tilt angle detection
Please adjust the handle properly to prevent tipping Handle tilt angle exceeds ±30° for over 3s Handle angle detection

III. Screen Notifications & Instructions

Voice Prompt Trigger Condition Action
Low battery, please return to base for charging Battery below 10% during cleaning Return to base for charging
Low water level, please refill water Water level below 10% during cleaning Refill clean water tank
Low water level, please add water before retrying Water level below 10% when self-cleaning starts Refill clean water tank
Low battery, will automatically self-clean after reaching 10% charge Battery below 10% when self-cleaning starts Charge until 10%, then start self-cleaning
To ensure cleaning performance, please replace the brush roller Brush replacement reminder Replace with a new brush

IV. Dirt Level Detection

  1. Smart Dirt Detection: Continuously monitors floor dirt levels. If dirt remains high for 30 seconds, a voice prompt will remind the user to perform self-cleaning.
  2. Screen Indicators for Dirt Levels:
    • Purple Ring: Low dirt level
    • Yellow Ring: Medium dirt level
    • Red Ring: High dirt level

V. Electrolyzed Water Sterilization Function

  1. Activation:
    • Automatically starts 3-5 seconds after power-on (not available in Quick Suction mode).
  2. Voice Prompt:
    • "Electrolyzed water sterilization is activated."
  3. Usage:
    • An animation will display for 3-5 seconds after activation, then simplify to a shield icon indicating active sterilization.

VI. Low-Clearance Cleaning Function

  1. Activation:
    • When the handle is tilted below 25° during cleaning, the fan speed will automatically adjust to low power.
  2. Voice Prompt:
    • "Low-clearance cleaning activated."
  3. Indicator:
    • First-time activation shows an animation; subsequent activations will display a tilted vacuum icon.
  4. Exit:
    • If the handle tilt exceeds 35° for over 2 seconds, low-clearance mode will deactivate.

VII. Product Maintenance

1. Cleaning Schedule

Component Maintenance Frequency
Wastewater tank Clean after each use
Antibacterial filter Clean after each use, replace every 3-6 months
Brush roller cover Clean as needed
Antibacterial brush roller Clean as needed, replace every 3-6 months
Machine air ducts Clean as needed
Base tray Clean as needed

2. Exterior Cleaning

  • Power off the machine before cleaning.
  • Wipe with a damp cloth (ensure it’s not too wet).

VIII. APP Connection

Note: Connecting to the app is optional; all cleaning functions work without the app.

  1. Place the device on the base:
    • Ensure the base is powered.
    • Ensure the vacuum is correctly positioned.
  2. Wake up the device:
    • Press the power button to turn on the screen.
    • Ensure Bluetooth is enabled on your phone.
  3. Connect via App:
    • Open the pairing mode in the app, bring the phone close to the device, and wait for automatic Bluetooth pairing.
Back to blog